<output id="zpptj"></output>

<output id="zpptj"></output>
<form id="zpptj"><form id="zpptj"><th id="zpptj"></th></form></form>

<form id="zpptj"><form id="zpptj"></form></form>

<em id="zpptj"><form id="zpptj"><track id="zpptj"></track></form></em>

      <form id="zpptj"><form id="zpptj"><th id="zpptj"></th></form></form>

      <em id="zpptj"></em>
      歡迎來到邁格奈特官方網站!如有任何疑問請撥打全國統一服務電話400-1122-958!

      新聞中心

      您當前所在位置:首頁 > 新聞中心 > 最新動態

      最新動態

      對于永磁除鐵器的日常維護你了解嗎?來看一下吧
      作者:管理員    發布于:2017-02-06 10:02:07   

      永磁除鐵器的維護保養是一項極其重要經常的工作,永磁除鐵器的日常維護應與極其的操作和檢修等密切配合,應有專職人員進行值班檢查。

      In addition to the maintenance of permanent magnet iron is an extremely important work often, permanent magnetic separators daily maintenance and operation and maintenance should be extremely close cooperation, should have professional staff for duty check.

      1、軸承擔負機器的全部負荷,所以良好的潤滑對軸承壽命有很大的關系,它直接影響到永磁除鐵器的使用壽命和運轉率,因而要求注入的潤滑油必須清潔,密封必須良好。永磁除鐵器的主要注油處:轉動軸承,軋輥軸承,所有齒輪,活動軸承、滑動平面;

      1, responsible for all load bearing of the machine, so good lubrication is greatly related to the bearing life, it directly affects the service life of the permanent magnetic separators and the rate of operation, thus requiringinto thelubricating must be clean, seal must be good. The permanent magnetic separator of the main oil: rolling bearing, roller bearing, all gear, a movable bearing, sliding plane;

      2、新安裝的輪箍容易發生松動必須經常進行檢查;

      2, the installation of the new tyre must be examined often prone to loose;

      3、注意永磁除鐵器各部位的工作是否正常;

      3, pay attention to the work of permanent magnet parts except iron is normal;

      4、注意檢查易磨損件的磨損程度,隨時注意更換被磨損的零件;

      4, pay attention to check the wear and tear of the wear parts, always pay attention to replace worn parts;

      5、放活動裝置的底架平面,應出去灰塵等物以免機器遇到不能破碎的物料時活動軸承不能在底架上移動,以致發生嚴重事故;

      A plane 5, active device, should go out dust to machine broken material cannot meet the movable bearing cannot move on the chassis, resulting in serious accidents;

      6、軸承油溫升高,應立即停車檢查原因加以消除;

      6, increase the bearing oil temperature, should stop and check the reason to be eliminated;

      7、轉動齒輪在運轉時若有沖擊聲應立即停車檢查并消除。

      7, the rotation of the gear in the operation of the impact of the sound should be stopped immediately to check and eliminate.




      ?
      400-1122-958